A Step-by-Step Overview to Installing a Bath Tub
A Step-by-Step Overview to Installing a Bath Tub
Blog Article
This article in the next paragraphs about A Step-by-Step Guide to Installing a Bathtub is without a doubt motivating. Have a go and make your own findings.
Mounting a tub isn't specifically rocket science, but it does need solid plumbing, woodworking, and often, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably challenging task. If the old tub is conveniently easily accessible, the project can relocate speedily; if you need to open up a wall to eliminate the old bathtub and place the brand-new tub, the job is much harder. In either situation, the task is within a home handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the new one. Make certain you have actually certified yourself for the job as well as are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed project, it is better to think about utilizing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This post will assist you set up a brand-new bath tub in your bathroom if you have already purchased a new bathtub as well as do not require to transform the plan of your previous water pipelines.
Your devices and also product list need to consist of the following:
Planning for the Installment
To start with, the supporting frame provided with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wooden boards are practical in evenly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub up until the level reviews level.
To mount faucets, fit all-time low of the outermost flexible tap port to the suitable supply pipe by making a compression sign up with; after that do the same for the other tap.
Activate the water supply and inspect all joints as well as brand-new pipework for leakages and tighten them if required. Fill the tub as well as additionally check the overflow outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the tub must wait up until the tub has actually been made use of at the very least when as this will certainly resolve it right into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making certain that the washing machines remain in place between the tap and the sink. Secure the tap in place with the producer offered backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap connectors. The former type should be connected to the tap finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, causing the water to penetrate the wall in between the bathroom and also the tiling, causing problems with dampness and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes and also cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not think about this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles utilizing waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that page about A Step-by-Step Guide to Installing a Bathtub when surfing around the internet. Sharing is good. Helping others is fun. Thank you for taking the time to read it.
Book Instantly
Report this page